linear bearing LM 38 38*57*76（d*D*L） - Bearing Catalogue

NINGBO SUNTHAI BEARING CO.,LTD SUNTHAI^® F&F^®
TEL：+86-574- 87222434 87220319 87220519 (EXT) 8013
FAX：0574-87223781 E-mail：stb888@sunthaibearing.com
ADD：NO.1730 LIYUAN NORTH ROAD, NINGBO, CHINA
WEBSITE：www.sunthaibearing.com www.fbearing.com

linear bearing LM 38 385776（dDL）

Post by ffbing, 2010-7-24, Views:

linear bearings（LM、LME、LMB series、KH series）

SUNTHAI bearing the characteristics of the three straight-line, uses, use the occasion

SUNTHAI is a straight line bearing low-cost production of linear motion systems, for unlimited travel with the cylinder axis with the use of. As a result of carrying the ball with the shaft contact point was therefore the use of small load. Ball minimal friction resistance to rotation, which can be smooth precision movement.

Linear bearings are widely used in electronic equipment, pull tester and the digital three-dimensional coordinate measuring device, such as precision equipment, as well as multi-axis machine tools, press, tool grinder, automatic gas cutting machine, printer, card sorting machine, food packaging machines and other industrial machinery sliding components. Grease lubrication: bearings straight into the internal anti-corrosion oil, if using oil lubrication, the first oil or organic solvents to remove anti-corrosion oil, then add dried grease. Recommend the use of sticky tags for N0.2 lithium soap grease. Lubricating oil: If oil lubrication, the corrosion is no need to remove the oil, according to temperature change can be selected ISO viscosity grade VG15-100 lubricating oil. Shaft for lubricating oil from the failed, or from the outside of the hole to the bearing pedestal oil. As the ring will scrape lubricating oil,lubricating oil does not apply non-porous bearings with seals.

Installation Notes:

Will be a straight line bearing load bearing should be used when the auxiliary work, to avoid a direct hit or face seals should be used evenly into bearings, with a buffer board, gently tapping with the optical axis penetration into linear bearings, shaft and bearings must be line of the centerline. If the axis is tilted insertion, ball may be off, or change caused by Cage, and damage to the linear bearings plus load should be evenly distributed throughout the bearing, in particular, bear the moment load should be used when two or more bearings. A straight line do not bear the rotating load bearing, or can lead to accidents. Suntai Bearing Linear model control, size, cross-references:

1. LM-GA, LME-GA, LMB-GA, LMK-GA, LMF-GA, LMT-GA KH-GA. GA on behalf of Steel Cage.

2. LM-UU, LME-UU, LMB-UU, LMK-UU, LMF-UU, LMT-UU KH-UU. UU Cage on behalf of nylon.

NINGBO SUNTHAI BEARING CO.,LTD

TEL:+86-0574-87222434 87220319 87220519(EXT)8008

FAX:+86-0574-87223781

ADD:NO.1730 LIYUAN NORTH ROAD, NINGBO, CHINA

E-MAIL:stb02@sunthaibearing.com

WEBSITE: www.sunthai.com.cn www.sunthaibearing.com SUNTHAI F&F BEARINGS

SUNTHAI NON STANDARD BEARING WEBSITE:www.fbearing.com

More products from SUNTHAI Series of Miniature Ball Bearing Series of Deep Groove Ball Bearing Plane Thust Bearings Series of Linear Bearing Center-Adjustable and Angular Contact Ball Bearing Needle Roller Bearing Cylindrical (Taper) Roller Bearings Centripetal Joint Bearing Non-Standard Ball Bearing

Tags:

Categories:Bearing Catalogue | Comments:0 | Quote:0 | Click here to access the log quoted TrackBack Address | Access to flow

上一篇：linear bearing LM 40 40*60*80（d*D*L）
下一篇：linear bearing LM 35 35*52*70（d*D*L）

maybe you are interested in the below article

Comments

发表评论:

◎Welcome to participate in the discussion, please post your views here, the exchange of your views.